Hallo zusammen,
ich verzweifel gerade ein bisschen an unsere neuen ASA 5505.
Ich möchte gerne eine Portweiterleitung von aussen an einen Webserver, der im internen Netzwerk steht erstellen. Ich habe nun das Cisco ASA 5500 Series Configuration Guide using the CLI Handbuch gewälzt sowie mehrere Tipps im Internet. Aber irgendwie will das alles nicht so richtig.
Ich bekomme im Logg immer folgenden Eintrag:
"TCP access denied by ACL from xx.xxx.xxx.xx/59518 to outside:yy.yyy.yyy.yy/80.
Wobei xx.xxx.xxx.xx die Adresse ist, von der ich versuche den Webserver aufzurufen und yy.yyy.yyy.yy die IP-Adresse des externe Ports ist.
Hier mal meine aktuelle config:
ASA Version 8.3(1)
!
hostname ciscoasa
names
!
interface Vlan1
nameif inside
security-level 100
ip address xx.x.x.x 255.0.0.0
!
interface Vlan2
nameif outside
security-level 0
ip address xx.xx.xx.xx xxx.xxx.xxx.xxx
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
ftp mode passive
dns domain-lookup inside
dns domain-lookup outside
dns server-group DefaultDNS
name-server xxx.xx.x.xx
name-server xxx.xx.x.xx
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network www
host xx.xx.x.x
object network Webserver
host xx.xx.x.x <=IP Webserver
object-group protocol TCPUDP
protocol-object udp
protocol-object tcp
access-list outside_access_in extended permit tcp any object Webserver eq www
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
nat (inside,outside) source dynamic any interface
!
object network obj_any
nat (inside,outside) dynamic interface
object network Webserver
nat (inside,outside) static interface service tcp www www
route outside 0.0.0.0 0.0.0.0 xx.xxx.xxx.xx 1 <=GW unsers ISP
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http xxx.xxx.x.x xxx.xxx.xxx.x inside
http xx.x.x.x xxx.x.x.x inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd dns xxx.xx.x.xx xxx.xx.x.xx
dhcpd auto_config outside
!
dhcpd address xx.x.x.x-xx.x.x.x inside
dhcpd dns xxx.xx.x.xx xxx.xx.x.xx interface inside
dhcpd enable inside
!
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
!
class-map inspection_default
match default-inspection-traffic
!
!
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
!
Wie Ihr gerade an der Config erkennen könnt bin ich CISCO Anfänger.
Mit den Tipps dieser Seite habe ich versucht das Portforwarding zu konfigurieren Link.
Vielleicht kann mir hier jemand helfen? :confused: