Jump to content

towi

Abgemeldet
  • Gesamte Inhalte

    3
  • Registriert seit

  • Letzter Besuch

Reputation in der Community

10 Neutral

Profile Fields

  • Member Title
    Gast
  1. towi

    Cisco 828

    Für alle die die Information gebrauchen können, ein Vorschlag: CISCO 828 (als Bridge) Mit Hyperterminal die Verbindung über COM1 herstellen. Nachdem der Router hochgefahren ist, die folgenden Befehle an der Befehlszeile des Routers (prompt = Router>) eingeben: enable configure terminal dadurch wechselt der Router in den Konfigurationsmodus, hier dann folgende Befehle eingeben (# markiert Bemerkungen): no ip routing ! interface Ethernet0 # Enter configuration Mode for the Ethernet inferface no ip address no ip directed-broadcast # (default) bridge-group 1 # specify the bridge-group number to which the Ethernet interface ! interface ATM0 # Enter configuration Mode for the ATM interface dsl equipment-type CPE # Achtung! Beim Gegenstück --> dsl equipment-type CO dsl linerate AUTO # Specify the G.SHDSL line rate. The range of valid numbers is between 72 and 2312 dsl operating-mode gshdsl symmetric annex B no ip address no ip directed-broadcast # (default) pvc 8/35 # Create an ATM PVC for each end node with which the router communicates encapsulation aal5snap ! bridge-group 1 # specify the bridge-group number to which the ATM interface belongs ! ip classless # (default) ! bridge 1 protocol ieee ! end # Exit the configuration mode for the ATM interface durch den Befehl end (bzw. strg-z) wechselt der Router wieder in seine normalen Umgebung zurück (prompt = Router>). Jetzt muss die Konfiguration nur noch gespeichert und der Router neugestartet werden, dazu folgenden Befehle an der Befehlszeile eingeben: write memory disable exit # Exit the configuration mode for the Ethernet interface and the router. und den Router aus- und wieder anschalten. Zur Information über den aktuellen Konfigurationsstand folgenden Befehl am Prompt eingeben: show running-config
  2. Habe es ausprobiert, leider funktioniert es dennoch nicht. Router#show interfrace f1 FastEthernet1 is up, line protocol is up Hardware is epif_port, address is 0008.e32a.f207 (bia 0008.e32a.f207) Internet address is 192.168.0.1/24 MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec) Auto-duplex, Auto Speed, 100BaseTX ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:00, output 00:00:56, output hang never Last clearing of "show interface" counters never Queueing strategy: fifo Output queue 0/40, 0 drops; input queue 0/75, 0 drops 5 minute input rate 26000 bits/sec, 3 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 4560 packets input, 4045160 bytes, 0 no buffer Received 3723 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 0 watchdog, 836 multicast 0 input packets with dribble condition detected 23 packets output, 7373 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out Router#
  3. Hallo, ich habe probleme beim konfigurieren der Steckplätze unseres Catalyst 2948G-L3 Switch: Router>enable Router#configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)#interface f1 Router(config-if)#ip address 192.168.000.001 255.255.255.000 Router(config-if)#no shutdown Router(config-if)#exit Router(config)#interface f2 Router(config-if)#ip address 192.168.000.002 255.255.255.000 Router(config-if)#no shutdown 192.168.0.0 overlaps with FastEthernet1 FastEthernet2: incorrect IP address assignment Router(config-if)# Diese Fehlermeldung kommt. Was muss ich anderes eingeben?
×
×
  • Neu erstellen...