Port-Chanel zwischen Catalyst 3750 und Nortel Passport 8600

[Chrisn 10]

Hallo zusammen,

ich habe ein kleines Problem, ich soll zwischen einem Cisco Catalyst 3750 Stack und einem Nortel Passport 8600 einen Etherchanel bzw. einen MLT konfigurieren, ich bin jetzt leider mit meinem latein am ende ;)

 

hier die config des 3750ers:

lacp system-priority 1
errdisable recovery cause channel-misconfig
no file verify auto
!
spanning-tree mode pvst
spanning-tree logging
spanning-tree portfast default
spanning-tree extend system-id
spanning-tree uplinkfast
!
vlan internal allocation policy ascending
!
vlan 32
name Test
!
vlan 33
name BackupVLAN_3750
!
vlan 1000
!
interface Port-channel5
switchport access vlan 32
switchport mode access
load-interval 30
duplex full
speed 100
spanning-tree portfast trunk
!
interface GigabitEthernet1/0/1
switchport access vlan 33
!

...

interface GigabitEthernet1/0/24
switchport access vlan 32
switchport mode access
duplex full
speed 100
channel-group 5 mode on


...

interface GigabitEthernet2/0/24
switchport access vlan 32
switchport mode access
duplex full
speed 100
channel-group 5 mode on
!
interface GigabitEthernet2/0/25
!
interface GigabitEthernet2/0/26
!
interface GigabitEthernet2/0/27
!
interface GigabitEthernet2/0/28
!
interface Vlan1
no ip address
no ip route-cache
shutdown
!
interface Vlan32
ip address 10.55.32.2 255.255.255.0
no ip route-cache
!
interface Vlan33
ip address 10.55.33.2 255.255.255.0
!
ip default-gateway 10.55.32.1
ip classless
ip http server

 

 

 

und ein auszug aus der config des passports

 

#
# PORT CONFIGURATION - PHASE I
#

ethernet 10/20 auto-recover-port enable
ethernet 10/21 auto-recover-port enable

#
# MLT CONFIGURATION
#

mlt 5 create
mlt 5 add ports 10/20-10/21
mlt 5 name "MLT-5-Catalyst3750"
mlt 5 perform-tagging enable

#

# STG CONFIGURATION
#

stg 1  add ports 10/20-10/21
stg 1  priority 1000

#
# VLAN CONFIGURATION
#

vlan 1 ports remove 1/1-1/2,10/1,10/10,10/20-10/21 member portmember
vlan 32 create byport 1 name "Test"
vlan 32 add-mlt 5
vlan 32 ports remove 1/1-1/8,10/1-10/19,10/22-10/48 member portmember
vlan 32 ports add 10/20-10/21 member portmember
vlan 32 ip create 10.55.32.1/255.255.255.0 mac_offset 1
vlan 33 create byport 1
vlan 33 ports remove 1/1-1/8,10/1-10/9,10/11-10/48 member portmember
vlan 33 ports add 10/10 member portmember
vlan 33 ip create 10.55.33.1/255.255.255.0 mac_offset 3
vlan 35 create byport 1
vlan 35 ports remove 1/3-1/8,10/1-10/48 member portmember
vlan 35 ports add 1/1-1/2 member portmember

vlan 35 ip create 10.55.35.1/255.255.255.0 mac_offset 2
vlan 1000 create byport 1
vlan 1000 ports remove 1/1-1/8,10/2-10/48 member portmember
vlan 1000 ports add 10/1 member portmember
vlan 1000 ip create 10.54.0.86/255.255.255.0 mac_offset 0

#
# PORT CONFIGURATION - PHASE II
#

ethernet 10/20 default-vlan-id 32
ethernet 10/20 auto-negotiate disable
ethernet 10/20 duplex full
ethernet 10/20 speed 100
ethernet 10/20 qos-level 0
ethernet 10/20 stg 1 faststart enable
ethernet 10/21 default-vlan-id 32
ethernet 10/21 auto-negotiate disable
ethernet 10/21 duplex full
ethernet 10/21 speed 100
ethernet 10/21 qos-level 0
ethernet 10/21 stg 1 faststart enable


#

[Chrisn 10]

da ich leider nur 4000 zeichen posten darf, hier der zweite teil.

 

 

folgendes hab ich aus dem logging des catalysten

1d00h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet2/0/24, changed state to up
1d00h: %LINEPROTO-5-UPDOWN: Line protocol on Interface Port-channel5, changed state to up
1d00h: %PM-4-ERR_RECOVER: Attempting to recover from channel-misconfig err-disable state on Gi1/0/24
1d00h: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/24, changed state to up
1d00h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/24, changed state to up
1d00h: %PM-4-ERR_DISABLE: channel-misconfig error detected on Gi1/0/24, putting Gi1/0/24 in err-disable state
1d00h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/24, changed state to down
1d00h: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet2/0/24, changed state to down
1d00h: %PM-4-ERR_DISABLE: channel-misconfig error detected on Gi2/0/24, putting Gi2/0/24 in err-disable state (Switch-2)
1d00h: %LINEPROTO-5-UPDOWN: Line protocol on Interface Port-channel5, changed state to down
1d00h: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan32, changed state to down
1d00h: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/24, changed state to down
1d00h: %LINK-3-UPDOWN: Interface Port-channel5, changed state to down
1d00h: %LINK-3-UPDOWN: Interface GigabitEthernet2/0/24, changed state to down

 

 

für irgendwelche ideen oder vorschläge bin ich dankbar

gruß

christian

[Frank04 10]

Hmm, mach mal das duplex full, speed 100 vom Channel weg. Dann mal mit no errdisable recovery cause channel-misconfig die automatische Abschaltung des Ports ausschalten. Bitte danach nochmal das Log posten.

 

Was sagt denn der Passport?

Configuring and displaying log files

The log commands allow you to configure and display the log files for the switch.

When the config bootconfig flags logging true command is saved in

the configuration file, the log entries are written to the /pcmcia/syslog.txt

file. If the logging flag is not set to true, the entries are stored in memory.

Writing log files

To write a log file, use the following command:

config log