Hallo... 
  
ich habe mir einen Router besorgt und komme nichmehr weiter.. 
  
Es ist ein 2611XM mit einer ADSL WIC over ISDN.. 
  
PVC 1/32  und 8/35 habe ich getestet..ohne erfolg...bekomme einfach keine IP über meinen Arcor Anschluss.. 
  
 
show run
Building configuration...
Current configuration : 1368 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router
!
boot-start-marker
boot-end-marker
!
!
no aaa new-model
no network-clock-participate slot 1 
no network-clock-participate wic 0 
ip cef
!
ip auth-proxy max-nodata-conns 3
ip admission max-nodata-conns 3
!
!
!
interface ATM0/1
description Arcor DSL
no ip address
no ip redirects
no ip unreachables
no atm ilmi-keepalive
dsl operating-mode auto 
dsl enable-training-log
pvc 8/35 
pppoe-client dial-pool-number 1
!
interface Dialer 1
mtu 1492
ip address negotiated
no ip redirects
no ip unreachables
ip nat outside
ip virtual-reassembly
encapsulation ppp
dialer pool 1
dialer-group 1
no cdp enable
ppp authentication chap callin
ppp chap hostname 123456
ppp chap password 7 dgdfgh
!
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 Dialer 1
!
ip http server
no ip http secure-server
ip nat inside source list 1 interface Dialer1 overload
!
dialer-list 1 protocol ip permit
!
!
control-plane
!
!
line con 0
line aux 0
line vty 0 4
login
!
!
end
**********************************************************************************************************
Router#show ip interface brief
Interface              IP-Address      OK? Method Status                Protocol
FastEthernet0/0      unassigned      YES NVRAM  administratively down down
ATM0/1                 unassigned      YES NVRAM  up                    up
FastEthernet0/1      unassigned      YES NVRAM  administratively down down
NVI0                     unassigned      NO  unset  up                    up
Dialer1                   unassigned      YES NVRAM  up                    up
Router#show interfaces atm 0/1
ATM0/1 is up, line protocol is up
 Hardware is DSLSAR (with Alcatel ADSL Module)
 Description: Arcor DSL _Modem_
 MTU 4470 bytes, sub MTU 4470, BW 736 Kbit/sec, DLY 690 usec,
    reliability 177/255, txload 1/255, rxload 1/255
 Encapsulation ATM, loopback not set
 Encapsulation(s): AAL5  AAL2, PVC mode
 23 maximum active VCs, 256 VCs per VP, 1 current VCCs
 VC Auto Creation Disabled.
 VC idle disconnect time: 300 seconds
Router#show dsl interface
ATM0/1
Alcatel 20166/20174 chipset information
               ATU-R (DS)                      ATU-C (US)
Modem Status:    Showtime (DMTDSL_SHOWTIME)
DSL Mode:        ITU G.992.1 (G.DMT) Annex B
ITU STD NUM:     0x01                            0x1
Vendor ID:       'ALCB'                          'BDCM'
Vendor Specific: 0x0000                          0x619D
Vendor Country:  0x00                            0xB5
Capacity Used:   90%                             86%
Noise Margin:     9.5 dB                         10.0 dB
Output Power:    13.0 dBm                        11.0 dBm
Attenuation:     11.0 dB                          7.0 dB
Defect Status:   None                            None
Last Fail Code:  None
Selftest Result: 0x00
Subfunction:     0xD0 (UR2)
Interrupts:      3895 (0 spurious)
PHY Access Err:  0
Activations:     1
LED Status:      ON
LED On Time:     100
LED Off Time:    100
Init FW:         embedded
Operation FW:    embedded
SW Version:      13.101
FW Version:      0xC166
                Interleave             Fast    Interleave              Fast
Speed (kbps):             0             6912             0               736
Cells:                    0                0             0           3380697
LOM Monitoring : Disabled
 
  
  
Please 
  
Thx 
Digi