MMAX

es funktioniert! ich habe den dialer interface eine ip zugewiesen und dem win router und es passt alles! von win zu win router klappt das ja auch ohne per apipa... naja wie dumm eigentlich aber egal hauptsache es geht endlich! noch eine letzte Frage die Verbindung besteht ca. 130 sec wie kann ich es einstellen das ich eine Stand-Verbindung habe?

Router#debug dialer events Dial on demand events debugging is on Router# *Mar 4 04:25:27.209: BR2/6:1: interface must be fifo queue, force fifo *Mar 4 04:25:27.209: %DIALER-6-BIND: Interface BR2/6:1 bound to profile Di10 *Mar 4 04:25:27.209: %LINK-3-UPDOWN: Interface BRI2/6:1, changed state to up *Mar 4 04:25:27.301: BR2/6:2: interface must be fifo queue, force fifo *Mar 4 04:25:27.305: %DIALER-6-BIND: Interface BR2/6:2 bound to profile Di10 *Mar 4 04:25:27.305: %LINK-3-UPDOWN: Interface BRI2/6:2, changed state to up *Mar 4 04:25:27.305: %ISDN-6-CONNECT: Interface BRI2/6:1 is now connected to 27 06 unknown *Mar 4 04:25:33.305: %ISDN-6-CONNECT: Interface BRI2/6:2 is now connected to 27 06 unknown *Mar 4 04:25:37.449: BR2/6:1 DDR: Remote name for Administrator *Mar 4 04:25:37.553: BR2/6:2 DDR: Remote name for Administrator *Mar 4 04:25:37.625: %ISDN-6-DISCONNECT: Interface BRI2/6:1 disconnected from 2706 Administrator, call lasted 10 seconds *Mar 4 04:25:37.625: %LINK-3-UPDOWN: Interface BRI2/6:1, changed state to down *Mar 4 04:25:37.629: BR2/6 DDR: has total 1 call(s), dial_out 0, dial_in 1 *Mar 4 04:25:37.629: %DIALER-6-UNBIND: Interface BR2/6:1 unbound from profile D i10 *Mar 4 04:25:38.553: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI2/6:2, changed state to up *Mar 4 04:25:42.765: %ISDN-6-DISCONNECT: Interface BRI2/6:2 disconnected from 2706 Administrator, call lasted 15 seconds *Mar 4 04:25:42.765: %LINK-3-UPDOWN: Interface BRI2/6:2, changed state to down *Mar 4 04:25:42.765: BR2/6 DDR: has total 0 call(s), dial_out 0, dial_in 0 *Mar 4 04:25:42.765: %DIALER-6-UNBIND: Interface BR2/6:2 unbound from profile D i10 *Mar 4 04:25:43.629: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI2/6:2, changed state to down Meine Neue Konfig: Router#sh run hostname Router ! username Administrator password 0 Password1 isdn switch-type basic-net3 interface BRI2/6 no ip address encapsulation ppp dialer pool-member 10 isdn switch-type basic-net3 isdn answer1 2704 isdn answer2 2705 isdn calling-number 2706 no fair-queue ppp authentication ms-chap ! interface Dialer10 no ip address encapsulation ppp dialer pool 10 dialer remote-name Administrator ppp authentication ms-chap callin ! gibt es noch etwas zu beachten auf win router seite?

debug ppp authentication *Mar 3 23:44:53.846: %LINK-3-UPDOWN: Interface BRI2/6:1, changed state to up *Mar 3 23:44:53.846: BR2/6:1 PPP: Using dialer call direction *Mar 3 23:44:53.846: BR2/6:1 PPP: Treating connection as a callin *Mar 3 23:44:53.954: %LINK-3-UPDOWN: Interface BRI2/6:2, changed state to up *Mar 3 23:44:53.954: %ISDN-6-CONNECT: Interface BRI2/6:1 is now connected to 27 06 unknown *Mar 3 23:44:53.958: BR2/6:2 PPP: Using dialer call direction *Mar 3 23:44:53.958: BR2/6:2 PPP: Treating connection as a callin *Mar 3 23:44:54.106: BR2/6:1 PPP: Authorization required *Mar 3 23:44:54.174: BR2/6:1 PAP: I AUTH-REQ id 12 len 28 from "Administrator" *Mar 3 23:44:54.174: BR2/6:1 PAP: Authenticating peer Administrator *Mar 3 23:44:54.174: BR2/6:1 PPP: Sent PAP LOGIN Request *Mar 3 23:44:54.178: BR2/6:1 PPP: Received LOGIN Response PASS *Mar 3 23:44:54.178: BR2/6:1 PPP: Sent LCP AUTHOR Request *Mar 3 23:44:54.178: BR2/6:1 LCP: Received AAA AUTHOR Response PASS *Mar 3 23:44:54.178: BR2/6:1 PAP: O AUTH-ACK id 12 len 5 *Mar 3 23:44:54.178: BR2/6:1 PPP: Sent CDPCP AUTHOR Request *Mar 3 23:44:54.178: BR2/6:1 CDPCP: Received AAA AUTHOR Response PASS *Mar 3 23:44:54.402: BR2/6:2 PPP: Authorization required *Mar 3 23:44:54.542: %ISDN-6-CONNECT: Interface BRI2/6:2 is now connected to 27 06 8636450452774439be15a9faf5d4778500000000 *Mar 3 23:44:54.542: %LINK-3-UPDOWN: Interface BRI2/6:1, changed state to down *Mar 3 23:44:54.570: BR2/6:2 PAP: I AUTH-REQ id 13 len 28 from "Administrator" *Mar 3 23:44:54.570: BR2/6:2 PAP: Authenticating peer Administrator *Mar 3 23:44:54.570: BR2/6:2 PPP: Sent PAP LOGIN Request *Mar 3 23:44:54.570: BR2/6:2 PPP: Received LOGIN Response PASS *Mar 3 23:44:54.574: BR2/6:2 PPP: Sent LCP AUTHOR Request *Mar 3 23:44:54.574: BR2/6:2 LCP: Received AAA AUTHOR Response PASS *Mar 3 23:44:54.574: BR2/6:2 PAP: O AUTH-ACK id 13 len 5 *Mar 3 23:44:54.574: BR2/6:2 PPP: Sent CDPCP AUTHOR Request *Mar 3 23:44:54.574: BR2/6:2 CDPCP: Received AAA AUTHOR Response PASS *Mar 3 23:44:54.826: %LINK-3-UPDOWN: Interface BRI2/6:2, changed state to down ich probiere mal das was rob gesagt hat mit ms-chap bzw ms-chapv2 aus!

so hab mal die debugs kopiert: das dialer interface brauche ich ja nur wenn ich vom cisco router aus den win2k Router anwählen will? wie gesagt ich will nur das sich der windows Router einwählt, der cisco muß/brauch das nicht ich habe meine config geändert auf: Current configuration : 1798 bytes ! version 12.3 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname Router ! boot-start-marker boot-end-marker ! ! username Administrator password 0 Password1 no aaa new-model ip subnet-zero interface BRI2/6 no ip address encapsulation ppp isdn switch-type basic-net3 isdn answer1 2704 isdn answer2 2705 ppp authentication pap meine Debugs: debug isdn q931 Router# *Mar 3 23:44:01.810: ISDN BR2/6 Q931: RX <- BAD PACKET() *Mar 3 23:44:01.842: ISDN BR2/6 Q931: RX <- SETUP pd = 8 callref = 0x15 Sending Complete Bearer Capability i = 0x8890 Standard = CCITT Transer Capability = Unrestricted Digital Transfer Mode = Circuit Transfer Rate = 64 kbit/s Channel ID i = 0x89 Calling Party Number i = 0x0080, '2706' Plan:Unknown, Type:Unknown Called Party Number i = 0x80, '2704' Plan:Unknown, Type:Unknown *Mar 3 23:44:01.842: %LINK-3-UPDOWN: Interface BRI2/6:1, changed state to up *Mar 3 23:44:01.846: ISDN BR2/6 Q931: TX -> CALL_PROC pd = 8 callref = 0x95 Channel ID i = 0x89 *Mar 3 23:44:01.886: ISDN BR2/6 Q931: TX -> CONNECT pd = 8 callref = 0x95 *Mar 3 23:44:01.918: ISDN BR2/6 Q931: RX <- BAD PACKET() *Mar 3 23:44:01.946: ISDN BR2/6 Q931: RX <- SETUP pd = 8 callref = 0x16 Sending Complete Bearer Capability i = 0x8890 Standard = CCITT Transer Capability = Unrestricted Digital Transfer Mode = Circuit Transfer Rate = 64 kbit/s Channel ID i = 0x8A Calling Party Number i = 0x0080, '2706' Plan:Unknown, Type:Unknown Called Party Number i = 0x80, '2704' Plan:Unknown, Type:Unknown *Mar 3 23:44:01.946: %LINK-3-UPDOWN: Interface BRI2/6:2, changed state to up *Mar 3 23:44:01.946: %ISDN-6-CONNECT: Interface BRI2/6:1 is now connected to 27 06 unknown *Mar 3 23:44:01.966: ISDN BR2/6 Q931: TX -> CALL_PROC pd = 8 callref = 0x96 Channel ID i = 0x8A *Mar 3 23:44:01.982: ISDN BR2/6 Q931: RX <- CONNECT_ACK pd = 8 callref = 0x15 Channel ID i = 0x89 *Mar 3 23:44:02.002: ISDN BR2/6 Q931: TX -> CONNECT pd = 8 callref = 0x96 *Mar 3 23:44:02.086: ISDN BR2/6 Q931: RX <- CONNECT_ACK pd = 8 callref = 0x16 Channel ID i = 0x8A *Mar 3 23:44:02.570: ISDN BR2/6 Q931: RX <- DISCONNECT pd = 8 callref = 0x15 Cause i = 0x8090 - Normal call clearing *Mar 3 23:44:02.570: %ISDN-6-CONNECT: Interface BRI2/6:2 is now connected to 27 06 8636450452774439be15a9faf5d4778500000000 *Mar 3 23:44:02.570: %LINK-3-UPDOWN: Interface BRI2/6:1, changed state to down *Mar 3 23:44:02.570: ISDN BR2/6 Q931: TX -> RELEASE pd = 8 callref = 0x95 Cause i = 0x8090 - Normal call clearing *Mar 3 23:44:02.678: ISDN BR2/6 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x15 Cause i = 0x8090 - Normal call clearing *Mar 3 23:44:02.874: ISDN BR2/6 Q931: RX <- DISCONNECT pd = 8 callref = 0x16 Cause i = 0x8090 - Normal call clearing *Mar 3 23:44:02.878: %LINK-3-UPDOWN: Interface BRI2/6:2, changed state to down *Mar 3 23:44:02.878: ISDN BR2/6 Q931: TX -> RELEASE pd = 8 callref = 0x96 Cause i = 0x8090 - Normal call clearing *Mar 3 23:44:02.966: ISDN BR2/6 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x16 Cause i = 0x8090 - Normal call clearing

Hallo, ich habe einen Cisco 3725 Router und habe vor eine Verbindung mit einem Win 2000 Router auf zubauen. Ich wähle mich per Ras-wählvervindung auf dem cisco ein Der Windows Server/ISDN-Nic ist auf DSS1 bzw isdn switch-type basic-net3 eingestellt Bei der Wählverbindung habe ich dem Server den username: "Administrator" und als Passwort: "Password1" vergeben doch die Verbindung wird kurz aufgebaut und danach wieder beendet? Der Windows Server hängt am NTBA mit den MSN Nummern 2704+2705 Der Cisco Router hängt am NTBA mit den MSN Nummern 2706+2707 ich denke mal es liegt ein Konfigurationsproblem vor. Ziel soll es sein: -Der Windows Server soll eine ständige Verbindung aufbauen am besten mit beiden Kanälen. was empfehlt ihr? als Authentifizierung ms-chap-v2? pap?...:confused: meine Debug Meldung: (isdn error) debug errors: Router# *Mar 1 00:16:44.643: ISDN BR2/6 SERROR: L2_Go: at bailout DLCB is NULL L2: sapi 0 tei 127 ces 0 ev 0x3 *Mar 1 00:16:44.667: ISDN BR2/6 SERROR: L2_Go: at bailout DLCB is NULL L2: sapi 0 tei 127 ces 0 ev 0x3 *Mar 1 00:16:44.667: %DIALER-6-BIND: Interface BR2/6:1 bound to profile Di10 *Mar 1 00:16:44.671: %LINK-3-UPDOWN: Interface BRI2/6:1, changed state to up *Mar 1 00:16:44.707: ISDN BR2/6 SERROR: L2_Go: at bailout DLCB is NULL L2: sapi 0 tei 127 ces 0 ev 0x3 *Mar 1 00:16:44.755: ISDN BR2/6 SERROR: L2_Go: at bailout DLCB is NULL L2: sapi 0 tei 127 ces 0 ev 0x3 *Mar 1 00:16:44.755: %DIALER-6-BIND: Interface BR2/6:2 bound to profile Di10 *Mar 1 00:16:44.755: %LINK-3-UPDOWN: Interface BRI2/6:2, changed state to up *Mar 1 00:16:44.755: %ISDN-6-CONNECT: Interface BRI2/6:1 is now connected to 2706 unkno wn *Mar 1 00:16:45.223: %ISDN-6-CONNECT: Interface BRI2/6:2 is now connected to 2706 efc30 f0147e54e549817d86af6def8f400000000 *Mar 1 00:16:45.223: %LINK-3-UPDOWN: Interface BRI2/6:1, changed state to down *Mar 1 00:16:45.223: %DIALER-6-UNBIND: Interface BR2/6:1 unbound from profile Di10 *Mar 1 00:16:45.575: %LINK-3-UPDOWN: Interface BRI2/6:2, changed state to down *Mar 1 00:16:45.575: %DIALER-6-UNBIND: Interface BR2/6:2 unbound from profile Di10 zur Überprüfung meine Konfig: version 12.3 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname Router ! boot-start-marker boot-end-marker ! ! username Administrator privilege 15 nohangup nocallback-verify password 0 Password1 no aaa new-model ip subnet-zero ! ! ip cef ! isdn switch-type basic-net3 ! interface BRI2/6 no ip address encapsulation ppp dialer pool-member 10 isdn switch-type basic-net3 isdn answer1 2704 isdn answer2 2705 isdn calling-number 2706 ppp authentication chap pap callin ! interface Dialer10 no ip address encapsulation ppp dialer pool 10 dialer string 2704 ppp authentication pap callin ppp chap hostname Administrator ppp chap password 0 Password1 ppp chap refuse ppp ms-chap refuse ppp ms-chap-v2 refuse ppp pap sent-username Administrator password 0 Password1 !