madona

Hi Fu123, danke fuer Deine Holfe. I versuche, den Switch durch networkkabel zu kontaktieren, aber es will nicht funktionieren. Ich heb' ihm die IP-adresse 10.0.0.2 gegeben und ich kann ihn "pingen" aber der kann Pakete senden aber nicht empfangen!!!! Ich moechte gerne den Flash und iso nochmal drauf spielen oder das Geraete HW-reseten. wo kann ich einen neuen Flash und iso fuer das Geraet downloaden. Ich danke Dir sehr. Madona

Hi Fu, die Ausgabe vom Booten: C2950 Boot Loader (C2950-HBOOT-M) Version 12.1(11r)EA1, RELEASE SOFTWARE (fc1) Compiled Mon 22-Jul-02 17:18 by antonino WS-C2950SX-24 starting... Base ethernet MAC Address: 00:0f:f7:ff:1b:40 Xmodem file system is available. Initializing Flash... flashfs[0]: 82 files, 3 directories flashfs[0]: 0 orphaned files, 0 orphaned directories flashfs[0]: Total bytes: 7741440 flashfs[0]: Bytes used: 5984768 flashfs[0]: Bytes available: 1756672 flashfs[0]: flashfs fsck took 7 seconds. ...done initializing flash. Boot Sector Filesystem (bs) installed, fsid: 3 Parameter Block Filesystem (pb) installed, fsid: 4 Loading "flash:/c2950-i6q4l2-mz.121-19.EA1c.bin"...### File "flash:/c2950-i6q4l2-mz.121-19.EA1c.bin" uncompressed and installed, entry point: 0x80010000 executing... Restricted Rights Legend Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph © of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph © (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013. Cisco Internetwork Operating System Software IOS C2950 Software (C2950-I6Q4L2-M), Version 12.1(19)EA1c, RELEASE SOFTWARE (fc2) Copyright © 1986-2004 by cisco Systems, Inc. Compiled Mon 02-Feb-04 23:29 by yenanh Image text-base: 0x80010000, data-base: 0x8058A000 Initializing flashfs... flashfs[1]: 82 files, 3 directories flashfs[1]: 0 orphaned files, 0 orphaned directories flashfs[1]: Total bytes: 7741440 flashfs[1]: Bytes used: 5984768 flashfs[1]: Bytes available: 1756672 flashfs[1]: flashfs fsck took 7 seconds. flashfs[1]: Initialization complete. Done initializing flashfs. POST: System Board Test : Passed POST: Ethernet Controller Test : Passed ASIC Initialization Passed POST: FRONT-END LOOPBACK TEST : Passed cisco WS-C2950SX-24 (RC32300) processor (revision J0) with 20808K bytes of memory. Processor board ID FHK0818Z16Z Last reset from system-reset Running Standard Image 24 FastEthernet/IEEE 802.3 interface(s) 2 Gigabit Ethernet/IEEE 802.3 interface(s) 32K bytes of flash-simulated non-volatile configuration memory. Base ethernet MAC Address: 00:0F:F7:FF:1B:40 Motherboard assembly number: 73-8135-07 Power supply part number: 34-0965-01 Motherboard serial number: FOC081702VD Power supply serial number: DAB081787SS Model revision number: J0 Motherboard revision number: A0 Model number: WS-C2950SX-24 System serial number: FHK0818Z16Z --- System Configuration Dialog --- Would you like to enter the initial configuration dialog? [yes/no]: no Press RETURN to get started! 00:00:14: %SPANTREE-5-EXTENDED_SYSID: Extended SysId enabled for type vlan 00:00:17: %SYS-5-RESTART: System restarted -- Cisco Internetwork Operating System Software IOS C2950 Software (C2950-I6Q4L2-M), Version 12.1(19)EA1c, RELEASE SOFTWARE (fc2) Copyright © 1986-2004 by cisco Systems, Inc. Compiled Mon 02-Feb-04 23:29 by yenanh 00:00:20: %LINK-5-CHANGED: Interface Vlan1, changed state to administratively down 00:00:21: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up 00:00:21: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to down 00:00:22: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down 00:00:23: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up Switch#show boot BOOT path-list: Config file: flash:/config.text Private Config file: flash:/private-config.text Enable Break: no Manual Boot: no HELPER path-list: NVRAM/Config file buffer size: 32768 Switch# Ich danke Dir sehr und hoffe, dass das Geraet wieder funftionieren wird. danke sehr nochmals madona:) :)

Hallo Fu, danke sehr fuer Deine schnelle Antwort. also nachdem die beiden g0/1 und g0/2 aufgehoert haben zu funktionieren, habe ich "show run" gemacht, und das ist das Ergaebniss: interface GigabitEthernet0/1 description **** LINK TO PE1 IN DIMMER ROOM **** switchport trunk native vlan 12 switchport trunk allowed vlan 12,101,130,140,150,200-202,500 switchport mode trunk no ip address ! interface GigabitEthernet0/2 no ip address ! interface Vlan1 no ip address no ip route-cache shutdown Danach habe ich den Switch resetet und das ist das Ergaebniss: Switch#show int g0/1 GigabitEthernet0/1 is down, line protocol is down (notconnect) Hardware is Gigabit Ethernet, address is 000f.f7ff.1b59 (bia 000f.f7ff.1b59) MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Auto-duplex, Auto-speed input flow-control is off, output flow-control is off ARP type: ARPA, ARP Timeout 04:00:00 Last input never, output 00:18:48, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 1 packets input, 64 bytes, 0 no buffer Received 0 broadcasts (0 multicast) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 0 multicast, 0 pause input 0 input packets with dribble condition detected 1 packets output, 64 bytes, 0 underruns Encapsulation ARPA, loopback not set Keepalive set (10 sec) Auto-duplex, Auto-speed input flow-control is off, output flow-control is off ARP type: ARPA, ARP Timeout 04:00:00 Last input never, output 00:18:48, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 1 packets input, 64 bytes, 0 no buffer Received 0 broadcasts (0 multicast) 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 0 multicast, 0 pause input 0 input packets with dribble condition detected 1 packets output, 64 bytes, 0 underruns 0 output errors, 0 collisions, 2 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 PAUSE output 0 output buffer failures, 0 output buffers swapped out GigabitEthernet0/2 is down, line protocol is down (notconnect) Hardware is Gigabit Ethernet, address is 000f.f7ff.1b5a (bia 000f.f7ff.1b5a) MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set ............

Hallo alle zusammen,:D Ich hab in der Firma, wo ich arbeite den Switch "WS-C2950SX-24 24 10/100 Mbps ports with two fixed 1000BASE-SX uplinks", der sehr gut lief. Alle 24 Ports + die 2 1000Base liefen bis vor 2 Tagen sehr gut und dann auf einmal haben beide "1000Base" Ports aufgehoert zu funktionieren. Alle Pc's, die in den 24-Ports angeschlossen waren, hatten keinen Internetvernindung mehr (beide 100Base Anschluesse sind mit dem Netzwerk durch Glassfaserkaebeln verbunden). Ich hab alles versucht, aber leider ohne Erfolg (Ich habe jeden 1000Base-Anschluss durch Glassfaserkabelen getestet, ohne Erfolg), Ich kriege die Leuchtdioden der beiden Anschluessen einfach nicht an. Hat irgendjemand von Euch bitte irgendeinen Vorschlag.:rolleyes: :rolleyes: Ich danke Euch allen Madona:)