Hallo erst mal und ein dankeschön an dieses forum
habe mir mit hilfe von dem forum und einem bekannten meine routerconfig zusammen gebastel. hatte zuanfang überhaut keinen plan wie das funzt. nun meine frage. habe ich die config so richtig gemacht? und was kann ich noch ändern und verbessern?
danke für eure hilfe im vorraus
crash
System Bootstrap, Version 11.1(12)XA, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
Copyright © 1997 by cisco Systems, Inc.
C1600 processor with 24576 Kbytes of main memory
program load complete, entry point: 0x4018060, size: 0x108968
%SYS-4-CONFIG_NEWER: Configurations from version 12.2 may not be correctly under
stood.
%Command or function not supported in this software
%A dialer must first be specified.
%SYS-3-CPUHOG: Task ran for 3000 msec (4/4), Process = Boot Load, PC = 40B513A
-Traceback= 407EB6E 407F628 407D118 40180E0 40005B0 4015C3E 40152B2 4014ED4 4002
5B8 4003086 4015636 40021A8 400C616program load complete, entry point: 0x2005000
, size: 0x9fcef8
Cisco Internetwork Operating System Software
IOS 1600 Software (C1600-SY-L), Version 12.2(8)T5, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright © 1986-2002 by cisco Systems, Inc.
Compiled Fri 21-Jun-02 11:13 by ccai
Image text-base: 0x0200544C, data-base: 0x02916BAC
cisco 1605 (68360) processor (revision C) with 18432K/6144K bytes of memory.
Processor board ID 08434223, with hardware revision 00000000
Bridging software.
X.25 software, Version 3.0.0.
2 Ethernet/IEEE 802.3 interface(s)
System/IO memory with parity disabled
8192K bytes of DRAM onboard 16384K bytes of DRAM on SIMM
System running from RAM
7K bytes of non-volatile configuration memory.
16384K bytes of processor board PCMCIA flash (Read/Write)
Router#sh run
Building configuration...
Current configuration : 1954 bytes
!
version 12.2
service timestamps debug uptime
service timestamps log uptime
service password-encryption
!
hostname Router
!
enable secret 5
!
ip subnet-zero
ip host-routing
ip name-server 62.26.26.62
ip name-server 195.185.185.195
!
vpdn enable
!
vpdn-group 1
request-dialin
protocol pppoe
ip mtu adjust
!
!
!
!
interface Ethernet0
ip address 192.168.1.1 255.255.255.0
ip nat inside
!
interface Ethernet1
no ip address
ip tcp adjust-mss 1452
no ip mroute-cache
pppoe enable
pppoe-client dial-pool-number 1
no cdp enable
!
interface Dialer1
ip address negotiated
ip mtu 1492
ip nat outside
encapsulation ppp
ip tcp adjust-mss 1452
no ip mroute-cache
dialer pool 1
dialer idle-timeout 60
dialer-group 1
no cdp enable
ppp authentication pap callin
ppp pap sent-username password
!
router rip
version 2
redistribute static
passive-interface Dialer1
network 192.168.1.0
no auto-summary
!
ip nat inside source list 102 interface Dialer1 overload
ip classless
ip route 0.0.0.0 0.0.0.0 Dialer1
no ip http server
ip pim bidir-enable
!
!
access-list 101 permit tcp 192.168.1.0 0.0.0.255 any eq www
access-list 101 permit tcp 192.168.1.0 0.0.0.255 any eq ftp
access-list 101 permit udp 192.168.1.0 0.0.0.255 any eq domain
access-list 101 permit tcp 192.168.1.0 0.0.0.255 any eq smtp
access-list 101 permit tcp 192.168.1.0 0.0.0.255 any eq pop3
access-list 102 deny udp any eq netbios-dgm any
access-list 102 deny udp any eq netbios-ns any
access-list 102 deny udp any eq netbios-ss any
access-list 102 deny udp any range snmp snmptrap any
access-list 102 deny udp any range bootps bootpc any
access-list 102 deny tcp any eq 137 any
access-list 102 deny tcp any eq 138 any
access-list 102 deny tcp any eq 139 any
access-list 102 permit ip any any
dialer-list 1 protocol ip list 101
!
!
line con 0
exec-timeout 0 0
line vty 0 4
login
!
end
