haha123
-
Gesamte Inhalte
13 -
Registriert seit
-
Letzter Besuch
Beiträge erstellt von haha123
-
-
ja aber ich kann das command nicht ausführen :mad: !!
-
So habe jetzt noch eine frage!!
Mehr als diese commands sind nicht möglich wie kann ich dann das flash erasen und dieses squeeze durchführen????
Router(boot)#?
clear Reinitialization functions, type "clear ?" for list
configure Configure from terminal or over network
connect <host> Connect to host - same as typing just a host name
copy copy flash tftp or tftp flash
debug Enable debugging functions, type "debug ?" for list
disable Turn off privileged commands
disconnect <cn> Break the connection specified by name or number
enable Turn on privileged commands
exit, quit, logout Exit from the EXEC
name-connection Give a connection a logical name
ping Send echo messages
reload Halt and reload system
resume Make the named connection be current
setup Initialize system configuration
show <cmd> Information commands, type "show ?" for list
systat Show terminal lines and users
telnet <host> Connect to host using telnet protocol
terminal Change terminal's parameters, type "terminal ?"
test Run hardware tests, type "test ?"
trace <address> Trace route to <address>
undebug Disable debugging functions, type "undebug ?" for list
where Show open connections
which-route Display CLNS route table lookup
write Write configuration memory, type "write ?" for list
<cr> To resume connection
Ich habe auch schon gesucht ich nehme einmal an das du das damit meinst aber ich kann diese commands nirgendwo ausführen???
Step 1 Obtain the IOS image from Cisco.com
Step 2 Access the router CLI using a Telnet connection or the console port.
Step 3 Delete your old Cisco IOS image from Flash, or to a Flash Disk, using the following CLI commands, and responding to the prompts as shown:
Router# delete <old IOS image name>
Delete filename [<old IOS image name>]? y
When prompted do NOT erase flash memory
Delete flash:y? [confirm] n
Delete flash:y aborted!
Router# squeeze flash:
If your router has a DOS file system, you do not need to use the squeeze flash: command.
If you are deleting the image from a Cisco 7000 router, you must specify the disk or slot from which you are deleting the file. Use the following CLI commands, and respond the prompts as shown:
Router# delete diskN:<old IOS image name>
Delete filename [<old IOS image name>]?
Delete diskN:<old IOS image name>?[confirm]
Router#
-
Ja mache ich wenn du mir sagst was ein squeeze ist dann bin ich bereit das zu machen!!! :rolleyes:
-
Habe jetzt noch einmal probiert vom tftp server das file herunterzuladen und jatzt sagt er das:
IP address or name of remote host [192.196.90.33]?
Name of file to copy ? c4000-i-mz.121-16
Copy c4000-i-mz.121-16 from 192.196.90.33 into Flash address space ? [confirm]
4194240 bytes available for writing without erasure.
Erase Flash address space before writing? [confirm]
bank 0...zzzzzzzzzzzzzzzzvvvvvvvvvvvvvvvveeeeeeeeeeeeeeee
bank 1...zzzzzzzzzzzzzzzzvvvvvvvvvvvvvvvveeeeeeeeeeeeeeee
bank 2...zzzzzzzzzzzzzzzzvvvvvvvvvvvvvvvveeeeeeeeeeeeeeee
bank 3...zzzzzzzzzzzzzzzzvvvvvvvvvvvvvvvveeeeeeeeeeeeeeee.................... [t
imed out]
-
Hilfeeeeee bitte bitte helft mir ich komme nicht weiter und ich würde das gerne entlich schaffen.
-
so habe es geschafft das IOS über den anderen router via tftp rüberzuholen aber jetzt geschieht das:
System Bootstrap, Version 4.14(3), SOFTWARE
Copyright © 1986-1993 by cisco Systems
4000 processor with 16384 Kbytes of main memory
Illegal IP keyword - classless
Booting c4000-i-mz.121-15.bin from Flash address space rrrrrrrrrrrrrrrrrrrrrrrrr
rrrrrrrrrrrrrrrrrrrrrrrrrrrrrrr
[OK - 3672772/16110938 bytes]
F3: 9248+3663492+165008 at 0x12000
Self decompressing the image : #################################################
####################################################Bus Error control register:
0x2ba0f0a9
ram byte 2 parity error
non-local memory transaction timeout
Bus Error, address: 0xea6344 at 0x12f3a (PC)
-
Lab_A(boot)#show flash
4096K bytes of Flash address space sized on CPU board.
Memory type is Flash.
File name/status
0 end
[4193672/4194304 bytes free/total]
hallo zu erst einmal vielen dank für deine schnelle antwort so habe jetzt aber ein sehr großes problem kein IOS mehr da habe noch eine frage ich habe noch einen zweiten 4000´er Router ich bilde mir ein wenn ich mich so dunkel daran zurück erinnere das man das IOS auf einen tftp server hochladen kann und dann könnte ich mir es ja von dort wieder runterladen oder hast du noch einen anderen tip??? ich bin wirklich für jede hilfe dankbar
-
Hallo so sieht der start von dem router aus
System Bootstrap, Version 4.14(3), SOFTWARE
Copyright © 1986-1993 by cisco Systems
4000 processor with 16384 Kbytes of main memory
Booting end from Flash address space
[OK - 566/16111674 bytes]
Undefined load module -- ignoring
System Bootstrap, Version 4.14(3), SOFTWARE
Copyright © 1986-1993 by cisco Systems
4000 processor with 16384 Kbytes of main memory
Booting end from Flash address space
[OK - 566/16111674 bytes]
Undefined load module -- ignoring
System Bootstrap, Version 4.14(3), SOFTWARE
Copyright © 1986-1993 by cisco Systems
4000 processor with 16384 Kbytes of main memory
Booting end from Flash address space
[OK - 566/16111674 bytes]
Undefined load module -- ignoring
System Bootstrap, Version 4.14(3), SOFTWARE
Copyright © 1986-1993 by cisco Systems
4000 processor with 16384 Kbytes of main memory
Booting end from Flash address space
[OK - 566/16111674 bytes]
Undefined load module -- ignoring
System Bootstrap, Version 4.14(3), SOFTWARE
Copyright © 1986-1993 by cisco Systems
4000 processor with 16384 Kbytes of main memory
Booting end from Flash address space
[OK - 566/16111674 bytes]
Undefined load module -- ignoring
System Bootstrap, Version 4.14(3), SOFTWARE
Copyright © 1986-1993 by cisco Systems
4000 processor with 16384 Kbytes of main memory
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
© of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
© (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
1525 O'Brien Drive
Menlo Park, California 94025
4000 Bootstrap Software (XX-RXBOOT), Version 9.14(3), RELEASE SOFTWARE
Copyright © 1986-1993 by cisco Systems, Inc.
Compiled Wed 15-Sep-93 14:43 by mlw
cisco 4000 (68030) processor (revision 0xA0) with 16384K/16384K bytes of memory.
Processor ID 5039027
DDN X.25 software, Version 2.0, NET2 and BFE compliant.
1 Ethernet/IEEE 802.3 interface.
2 Serial network interfaces.
128K bytes of non-volatile configuration memory.
4096K bytes of Flash address space sized on CPU board.
--- System Configuration Dialog ---
Refer to the 'Getting Started' Guide for additional help.
Default settings are in square brackets '[]'.
Configuring interface Ethernet0:
Is this interface in use? [yes]: no
Configuring interface Serial0:
Is this interface in use? [yes]: no
Configuring interface Serial1:
Is this interface in use? [yes]: no
Press RETURN to get started!
Router(boot)>
-
Hallo habe eine frage bezüglich Cisco ich weiß es geht hier um den MCSE aber ich weiß nicht wo es ein Forum über Cisco Router gibt!
Habe folgendes Problem meine Cisco kenntnise sind leider schon etwas eingerostet, habe einen 4000 Router mit IOS Version 12.0
wenn ich das Ding einschalte startet er normal aber sobald ich mich angemeldet habe kommt: router(boot)> ich weiß leider nichtmehr wie ich in den normalmodus zurückkehren kann habe auch schon ziemlich lange im internet gesucht kann aber leider nichts finden.
Bitte ich brauche dringend irgendeine HILFE.
Schon mal vielen Dank im vorraus
-
Ich gebe euch da absolut recht der MCSE Status sinkt aber ich denke dass dieses nicht immer an der Ausbildung liegt sondern an den vielen Hilfsmitteln die mittlerweile vorhanden sind.
Aber wenn wir uns ein bisschen an die Schule zurückerinnern wurden wir also zumindest war das bei mir so auch auf Prüfungen vorbereitet
Ich finde es schon wichtig das es Organisationen gibt die auch für Berufsumsteiger diese Maßnahmen anbieten.
Auch ich bin so ein Umsteiger und habe durch viel lernwille- und Kampf den weiten WEG zum MCSE geschafft.
Ich denke das es auch nicht an irgendwelchen pseudo- Organisationen liegt sondern immer nur an den Leuten die an so einer Maßnahme teilnehmen und es ist natürlich auch eine Sache der Motivation sowie Teamgeist und wille die manche Leute so gar nicht an den tag bringen. Aber es stimmt schon natürlich ist es gut wenn man bei so einer Maßnahme Praxis vorweisen kann.
Aber mit Lerngeist kann man auch dieses Hindernis überwinden und es auch zu einem wirklichen MCSE schaffen. Ich habe es ja auch geschafft. Und ich kann mir nicht vorstellen das es irgendeine Organisation gibt die es zulässt einen unqualifizierten Trainer in so eine Maßnahme hineinzustellen und dann die Leute irgendwelche Prüfungsfragen auswendig lernen zu lassen.
Da glaube ich würden die Leute auch einen Aufstand machen da dies absolut keinen sinn machen würde.
Auch wie du sagst ein junger Trainer kann natürlich ein Problem sein aber ein guter Freund von mir ist auch Trainer und sehr jung und ich denke er macht seinen Job sehr gut. Das alter sagt nicht alles über einen Menschen aus
-
he hast du die bücher noch zu verkaufen wäre sehr daran interresiert!!!
-
Was ich weiß sind das doch vier Prüfungen und die sind in englisch
aber ich hätte da noch einige günstige bücher für dich zu verkaufen
CISCO Router
in Cisco Forum — Allgemein
Geschrieben
Hallo vielen dank für die hilfe aber es hat nichts genützt ich gebe es auf ich weiß nichtmehr was ich machen soll!!!
Er schreibt jetzt immer noch das gleiche ich zeigs dir einmal:
Refer to the 'Getting Started' Guide for additional help.
Default settings are in square brackets '[]'.
Configuring interface Ethernet0:
Is this interface in use? [yes]: yes
Media-type 10BaseT or AUI? [AUI]: 10BaseT
IP address for this interface: 192.196.90.1
Number of bits in subnet field [0]: 0
Class C network is 192.196.90.0, 0 subnet bits; mask is 255.255.255.0
Configuring interface Serial0:
Is this interface in use? [yes]: no
Configuring interface Serial1:
Is this interface in use? [yes]: no
Press RETURN to get started!
Router(boot)>ena
Router(boot)#copy tftp flash
File name/status
0 c4000-i-mz.121-15.bin
[521468/4194304 bytes free/total]
IP address or name of remote host [255.255.255.255]? 192.196.90.22
Name of file to copy ? c4000-i-mz.121-15.bin
File 'c4000-i-mz.121-15.bin' already exists; it will be invalidated!
Copy c4000-i-mz.121-15.bin from 192.196.90.22 into Flash address space ? [confi
rm]
521404 bytes available for writing without erasure.
Erase Flash address space before writing? [confirm]
bank 0...zzzzzzzzzzzzzzzzvvvvvvvvvvvvvvvveeeeeeeeeeeeeeee
bank 1...zzzzzzzzzzzzzzzzvvvvvvvvvvvvvvvveeeeeeeeeeeeeeee
bank 2...zzzzzzzzzzzzzzzzvvvvvvvvvvvvvvvveeeeeeeeeeeeeeee
bank 3...zzzzzzzzzzzzzzzzvvvvvvvvvvvvvvvveeeeeeeeeeeeeeee
Loading from 192.196.90.22: !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!! [OK - 3672772/4194240 bytes]
Verify checksum...vvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvv
Verification successful: Length = 3672772, checksum = 0xD173
Router(boot)#configure terminal
Enter configuration commands, one per line.
Edit with DELETE, CTRL/W, and CTRL/U; end with CTRL/Z
config-register 0x2102
exit
Unrecognized configuration command - exit
Warning: This bootstrap image is only for netbooting the final image
and does not support the full command set.
^Z
Router(boot)#reload
[confirm]
System Bootstrap, Version 4.14(3), SOFTWARE
Copyright © 1986-1993 by cisco Systems
4000 processor with 16384 Kbytes of main memory
Booting c4000-i-mz.121-15.bin from Flash address space rrrrrrrrrrrrrrrrrrrrrrrrr
rrrrrrrrrrrrrrrrrrrrrrrrrrrrrrr
[OK - 3672772/16111674 bytes]
F3: 9248+3663492+165008 at 0x12000
Self decompressing the image : #################################################
####################################################Bus Error control register:
0x2ba0f0a9
ram byte 2 parity error
non-local memory transaction timeout
Bus Error, address: 0xea6344 at 0x12f3a (PC)
Vielleicht weißt du noch eine möglichkeit ich könnte mir vielleicht auch denken das, das file auf dem router nicht funktioniert aber mein zweiter 4000 router hat genau das gleiche file und er funktioniert einwandfrei