Cisco 2811 CCME ISDN Problem

[Gulaschkanone]

Hab ein Problem mit der Telefonanlage an meinen 2811er und zwar kann ich einfach keine Verbindung mit dem Tel/Handy von extern nach innen aufbauen, da kommt immer besetzt.
Genauso ich kann auch nicht rauswählen.
Hat da jemand eine Idee?

Hier meine config:

trunk group Telekom

hunt-scheme round-robin

!

!

!

!

!

!

voice translation-rule 1

rule 1 /^.*/ /<meine_tel>/

!

voice translation-rule 2

rule 1 /^<meine_tel>0$/ /210/

!

voice translation-rule 3

rule 1 /^<meine_tel_>\([0-2]..\)$/ /\1/

!

!

voice translation-profile CALLER_ID_xxxxx

translate calling 1

!

voice translation-profile Telekom_in_0_2

translate called 2

!

voice translation-profile Telekom_in_3

translate called 3
interface BRI0/3/0

no ip address

trunk-group Telekom

!

interface BRI0/3/1

no ip address

trunk-group Telekom

tftp-server flash:/phone/7940-7960/P00308000500.bin alias P00308000500.bin

tftp-server flash:/phone/7940-7960/P00308000500.loads alias P00308000500.loads

tftp-server flash:/phone/7940-7960/P00308000500.sb2 alias P00308000500.sb2

tftp-server flash:/phone/7940-7960/P00308000500.sbn alias P00308000500.sbn

!

!

control-plane

!

!

voice-port 0/3/0

connection plar 1500

!

voice-port 0/3/1

connection plar 1500

dial-peer cor custom

!

!

dial-peer voice 1 pots

trunkgroup Telekom

description Telekom_out

translation-profile outgoing CALLER_ID_<meine_tel>

destination-pattern <meine_tel>T

forward-digits all

!

dial-peer voice 2 pots

description Telekom_in_0

translation-profile incoming Telekom_in_0_2

incoming called-number <meine_tel>T

direct-inward-dial

port 0/3/0

!

dial-peer voice 3 pots

description Telekom_in_0

translation-profile incoming Telekom_in_0_2

incoming called-number <meine_tel>T

direct-inward-dial

port 0/3/1

!

dial-peer voice 4 pots

description Telekom_in

translation-profile incoming Telekom_in_3

incoming called-number <meine_tel>[0-2]..

direct-inward-dial

port 0/3/0

!

dial-peer voice 5 pots

description Telekom_in

translation-profile incoming Telekom_in_3

incoming called-number <meine_tel>[0-2]..

direct-inward-dial

port 0/3/1

!




Wenn noch was gebraucht wird, einfach bescheid sagen.

[blackbox]

Hi

was haben wir den auf dem ISDN Point to Point (Anlagenanschluß) oder Point to Multipoint (MSN) - dann mal die BRI´s debuggen - was die so meinen und die passenden Config Zeilen posten - damit man weiss ob der Bereich passt - dann sollten wir uns die Voice rules ansehen - wenn wir wissen was ankommt.

[Gulaschkanone]

kannst du mir da die Befehle geben?

kenn mich überhaupt nicht in Voice aus

achja, es ist ein Anlagenanschluss, wir haben Gesamt 5 Leitungen, aktuell teste ich mit 2 Leitungen

[Gulaschkanone]

bekomm bei debug isdn all immer folgenden Fehler:

Sep 26 18:18:24.362: ISDN **ERROR**: isdn_iqueue: called without a switch type
Sep 26 18:18:25.346: %SYS-3-INVMEMINT: Invalid memory action (malloc) at interrupt level -Traceback= 0x44A60BC0z 0x41C66988z 0x41C66AA0z 0x4070A064z 0x406EAE5Cz 0x40735F98z 0x4027A9F0z 0x4027B0F8z 0x41149274z 0x40F55F34z 0x4000FA40z 0x400119F4z

[blackbox]

Hi,

das denke ich mir. Hast du den Befehl "isdn switch type....." in der Config?

Hier ein Auszug aus einer Config mit Anlagenanschluß :

interface BRI0/1/0
no ip address
isdn switch-type basic-net3
isdn timer T310 10000
isdn overlap-receiving T302 10000
isdn tei-negotiation first-call
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn outgoing-voice info-transfer-capability 3.1kHz-audio
isdn static-tei 0
isdn skipsend-idverify
.....

[Gulaschkanone]

Vielen Dank.
Jetzt bekomm ich immer "kein Anschluss unter dieser Nummer"

hier mal die ganze Config:

Router_1#sh run
Building configuration...


Current configuration : 15478 bytes
!
! Last configuration change at 05:08:58 CTE Mon Sep 27 2010
!
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname Router_1
!
boot-start-marker
boot system flash c2800nm-advipservicesk9-mz.151-2.T1.bin
boot-end-marker
!
!
logging buffered 51200 warnings
!

multilink bundle-name authenticated
!
isdn switch-type basic-net3
!
!
trunk group Telekom
!
!
!
voice translation-rule 1
rule 1 /^xxxx298430$/ /210/
!
voice translation-rule 2
rule 1 /^xxxx29843\([0-2]..\)$/ /\1/
!
!
voice translation-profile CALLER_ID_xxxx29843
!
voice translation-profile Telekom_2
translate called 2
!
voice translation-profile Telekom_in_0_2
!
voice translation-profile Telekom_in_1
translate called 1
!
voice translation-profile Telekom_in_3
!
!
voice-card 0
dsp services dspfarm
!
!
interface BRI0/3/0
no ip address
isdn switch-type basic-net3
isdn timer T310 10000
isdn overlap-receiving T302 10000
isdn tei-negotiation first-call
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn outgoing-voice info-transfer-capability 3.1kHz-audio
isdn static-tei 0
isdn skipsend-idverify
trunk-group Telekom
!
interface BRI0/3/1
no ip address
isdn switch-type basic-net3
isdn timer T310 10000
isdn overlap-receiving T302 10000
isdn tei-negotiation first-call
isdn point-to-point-setup
isdn incoming-voice voice
isdn send-alerting
isdn sending-complete
isdn outgoing-voice info-transfer-capability 3.1kHz-audio
isdn static-tei 0
isdn skipsend-idverify
trunk-group Telekom
!
!
tftp-server flash:/phone/7940-7960/P00308000500.bin alias P00308000500.bin
tftp-server flash:/phone/7940-7960/P00308000500.loads alias P00308000500.loads
tftp-server flash:/phone/7940-7960/P00308000500.sb2 alias P00308000500.sb2
tftp-server flash:/phone/7940-7960/P00308000500.sbn alias P00308000500.sbn
!
control-plane
!
!
voice-port 0/3/0
connection plar 1500
!
voice-port 0/3/1
connection plar 1001
!
!
!
sccp local FastEthernet0/0.2
sccp
!
dial-peer cor custom
!
!
dial-peer voice 1 pots
description Telekom_in
translation-profile incoming Telekom_in_1
incoming called-number xxxx98430
direct-inward-dial
port 0/3/0
!
dial-peer voice 2 pots
description Telekom_in
translation-profile incoming Telekom_in_1
incoming called-number xxxx98430
direct-inward-dial
port 0/3/1
!
dial-peer voice 3 pots
description Telekom
translation-profile incoming Telekom_2
incoming called-number xxxx9843[0-2]..
direct-inward-dial
port 0/3/0
!
dial-peer voice 4 pots
description Telekom
translation-profile incoming Telekom_2
incoming called-number xxxx9843[0-2]..
direct-inward-dial
port 0/3/1
!
!
!
!
telephony-service
no auto-reg-ephone
max-ephones 35
max-dn 40
ip source-address 192.168.201.254 port 2000
system message yyyy
load 7960-7940 P00308000500.loads
time-zone 23
time-format 24
date-format dd-mm-yy
dialplan-pattern 1 xxxx9843 extension-length 3
max-conferences 8 gain -6
moh flash:/music-on-hold.au
transfer-system full-consult
!
!

[blackbox]

Und dann mal wieder den Debug auf "isdn q931 & q921"

[Gulaschkanone]

hab gerade einen anruf von der Telekom bekommen, der freundliche Techniker meinte da fehlt noch ein cause Wert.

Kannst du damit was Anfangen?

[blackbox]

Das ist zu allgemein - daher mal das Debug

[Gulaschkanone]

Sep 27 09:52:49.100: ISDN BR0/3/0 Q921: User RX <- RRp sapi=0 tei=0 nr=1
Sep 27 09:52:49.104: ISDN BR0/3/0 Q921: User TX -> RRf sapi=0 tei=0 nr=1
Sep 27 09:52:51.364: ISDN BR0/3/1 Q921: User TX -> RRp sapi=0 tei=0 nr=2
Sep 27 09:52:51.404: ISDN BR0/3/1 Q921: User RX <- RRp sapi=0 tei=0 nr=3
Sep 27 09:52:51.404: ISDN BR0/3/1 Q921: User TX -> RRf sapi=0 tei=0 nr=2
Sep 27 09:52:51.408: ISDN BR0/3/1 Q921: User RX <- RRf sapi=0 tei=0 nr=3
Sep 27 09:52:59.100: ISDN BR0/3/0 Q921: User RX <- RRp sapi=0 tei=0 nr=1
Sep 27 09:52:59.100: ISDN BR0/3/0 Q921: User TX -> RRf sapi=0 tei=0 nr=1
Sep 27 09:53:01.364: ISDN BR0/3/1 Q921: User RX <- RRp sapi=0 tei=0 nr=3
Sep 27 09:53:01.364: ISDN BR0/3/1 Q921: User TX -> RRf sapi=0 tei=0 nr=2
Sep 27 09:53:09.176: ISDN BR0/3/1 Q921: User RX <- INFO sapi=0 tei=0, ns=2 nr=3
Sep 27 09:53:09.176: ISDN BR0/3/1 Q931: SETUP pd = 8 callref = 0x01
Bearer Capability i = 0x8090A3
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0x89
Exclusive, B1
Calling Party Number i = 0x2181, '###67294'
Plan:ISDN, Type:National
Called Party Number i = 0xC1, '###432'
Plan:ISDN, Type:Subscriber(local)
High Layer Compat i = 0x9181
Sep 27 09:53:09.180: ISDN BR0/3/1 Q921: User TX -> RR sapi=0 tei=0 nr=3
Sep 27 09:53:09.188: ISDN BR0/3/1 Q921: User TX -> INFO sapi=0 tei=0, ns=3 nr=3
Sep 27 09:53:09.188: ISDN BR0/3/1 Q931: SETUP_ACK pd = 8 callref = 0x81
Channel ID i = 0x89
Exclusive, B1
Sep 27 09:53:09.204: ISDN BR0/3/1 Q921: User RX <- RR sapi=0 tei=0 nr=4
Sep 27 09:53:09.212: ISDN BR0/3/1 Q921: User TX -> INFO sapi=0 tei=0, ns=4 nr=3
Sep 27 09:53:09.212: ISDN BR0/3/1 Q931: DISCONNECT pd = 8 callref = 0x81
Cause i = 0x8081 - Unallocated/unassigned number
Sep 27 09:53:09.228: ISDN BR0/3/1 Q921: User RX <- RR sapi=0 tei=0 nr=5
Sep 27 09:53:09.264: ISDN BR0/3/1 Q921: User RX <- INFO sapi=0 tei=0, ns=3 nr=5
Sep 27 09:53:09.264: ISDN BR0/3/1 Q931: INFORMATION pd = 8 callref = 0x01
Called Party Number i = 0xC1, '1'
Plan:ISDN, Type:Subscriber(local)
Sep 27 09:53:09.264: ISDN BR0/3/1 Q921: User TX -> RR sapi=0 tei=0 nr=4
Sep 27 09:53:09.284: ISDN BR0/3/1 Q921: User RX <- INFO sapi=0 tei=0, ns=4 nr=5
Sep 27 09:53:09.284: ISDN BR0/3/1 Q931: RELEASE pd = 8 callref = 0x01
Sep 27 09:53:09.284: ISDN BR0/3/1 Q921: User TX -> RR sapi=0 tei=0 nr=5
Sep 27 09:53:09.288: ISDN BR0/3/1 Q921: User TX -> INFO sapi=0 tei=0, ns=5 nr=5
Sep 27 09:53:09.288: ISDN BR0/3/1 Q931: RELEASE_COMP pd = 8 callref = 0x81
Sep 27 09:53:09.304: ISDN BR0/3/1 Q921: User RX <- RR sapi=0 tei=0 nr=6
Sep 27 09:53:18.360: ISDN BR0/3/1 Q921: User RX <- RRp sapi=0 tei=0 nr=6
Sep 27 09:53:18.360: ISDN BR0/3/1 Q921: User TX -> RRf sapi=0 tei=0 nr=5
Sep 27 09:53:19.100: ISDN BR0/3/0 Q921: User RX <- RRp sapi=0 tei=0 nr=1
Sep 27 09:53:19.100: ISDN BR0/3/0 Q921: User TX -> RRf sapi=0 tei=0 nr=1
Sep 27 09:53:28.360: ISDN BR0/3/1 Q921: User TX -> RRp sapi=0 tei=0 nr=5
Sep 27 09:53:28.364: ISDN BR0/3/1 Q921: User RX <- RRp sapi=0 tei=0 nr=6
Sep 27 09:53:28.364: ISDN BR0/3/1 Q921: User TX -> RRf sapi=0 tei=0 nr=5
Sep 27 09:53:28.412: ISDN BR0/3/1 Q921: User RX <- RRf sapi=0 tei=0 nr=6
Sep 27 09:53:29.100: ISDN BR0/3/0 Q921: User TX -> RRp sapi=0 tei=0 nr=1
Sep 27 09:53:29.100: ISDN BR0/3/0 Q921: User RX <- RRp sapi=0 tei=0 nr=1
Sep 27 09:53:29.100: ISDN BR0/3/0 Q921: User TX -> RRf sapi=0 tei=0 nr=1
Sep 27 09:53:29.132: ISDN BR0/3/0 Q921: User RX <- RRf sapi=0 tei=0 nr=1
Sep 27 09:53:38.404: ISDN BR0/3/1 Q921: User RX <- RRp sapi=0 tei=0 nr=6
Sep 27 09:53:38.404: ISDN BR0/3/1 Q921: User TX -> RRf sapi=0 tei=0 nr=5
Sep 27 09:53:39.100: ISDN BR0/3/0 Q921: User RX <- RRp sapi=0 tei=0 nr=1
Sep 27 09:53:39.100: ISDN BR0/3/0 Q921: User TX -> RRf sapi=0 tei=0 nr=1

das bekomm ich als Debug